- ✔【Easy to Grab】Compact size, lightweight, easy to grab..
- ✔【Saving Your Power】It can save 3-5 times than man power by hand..
- ✔【Safety & Credibility】It is a miniature motor tool has the trait of safety and credibility..
- ✔【Used for Building Market】Including civil building, floor pipe, heating floor mesh, steel bar, etc..
- ✔【Advantages】Reasonable structure, advanced craft, simple and convenient operation, high efficiency and convenient maintenance..
- ›See more product details.
Product description
-------------------
Specifications:
Color:Red / Green(for choice)
Material: Plastic + Metal
Voltage: 10.8V
Battery: Lithium Ion Batteries
Battery Capacity: 1500 mAh
Battery Charging Time: 1.5 hours full filling
Tying Wire Diameter: 0.8mm
Tying Wire Length: more than 110 m
Applicable Of Steel Strapping: 8mm - 34mm
Knot Wire Length: 300 - 500mm
Knot Number Per Charge: 1500 times
Knot The Required Time: 0.8 seconds at a time
Machine Size: 275 mm * 65 mm * 240 mm /
10.83''x2.56''x9.45''(appr.)
Tying Wire Installations:
1. In the state of start-up, press the locking plate of the
opening wire plate, open the plate cover.
2. Take out the tying wire, tear the packaging film, pull
straight wire head about 10 cm, load into the binding machine in
the clockwise direction, the wire head into the guide tap tube.
Note: Clench the wire plate when tear the packaging film, do not
let the wire loose. If the wire is free to disperse, it will lead
to the spread of the wire stuck in the wire plate.
3. Insert the head of the wire guide into the tap pipe until it
is resisted.
4. Cover the plate and fasten the locking piece.
5. Pinch the wire forward with two fingers, press and hold the
switch and send the wire out.
6. If you want to take out the wire plate when finished, press
and hold the locking piece, open the wire plate cover plate,
holding the wire tray to the side and pull out.
Package included:
1X Tying Machine
1X Pliers
1X Charger
1X Storage Box
2X Lithium Ion Batteries
1X Tying Wire in the machine (Tying Wire Standard: About 0.8 mm
x 110 m/roll)
Notice:
Please allow 1-3cm error due to manual measurement and make sure
you do not mind before ordering.
Please understand that colors may exist chromatic aberration as
the different placement of pictures.
Legal Discler
----------------
Operation Instructions:
1. The rebar tirer's jaws are stuck to the intersection of the
steel bars, and the steel bars are hooked at 45 degree angles.
Note: There can be no barrier between the mouth of the jaws and
the wire.
2. Press the start switch, the rebar tirer machine carries on
the work (spins, hinges tightly, cuts off)
Note: Press one button at a time, do not probe the jaws at work.
3. When automatic completion, the jaw from the steel bar
intersection and then pull back, complete the process and prepare
for the next binding.
4. When the binding process is not completed, do not unplug the
machine in advance, otherwise it will cause the bundling of the
goods tied skidding.
Operating Skills:
1. In use, the left tilt 45 degrees after banding, the next time
the banding into a right tilt 45 degrees banding, left and right
alternately banding.
2. When the machine is about to tighten, the machine will appear
slightly shaking, while holding the hand of the machine not too
tight, you can relax properly.
Maintenance:
1. Clean the machine regularly, keep the wire mouth clean.
2. This product can not be placed randomly, so as not to cause
damage to parts.
3. Batteries must not be placed together with other metal
objects to avoid short circuit.
4. Non-professional do not disassemble the machine arbitrarily,
lest cause damage.
5. When you encounter an unresolved failure, please give it to
the professional repair.