RioRandDMX512 LED Signal Splitter Amplifier Distributor 1 Way in 8-Channel 3-Pin Output with Signal Indicator

The device feels like what you would expect for the price point, but it works great and does what it claims. Some of the other options in the $50-$70 range claim to be optically isolated but are not.The seller is definitely listening to feedback, as mine included a power adapter, as well as the bare wire lead, and this one has a status light/signal indicator.Unless you want to get one of the $300+ units, this is really the best option.

Just got two of these and they work perfectly. Checked the insides and they are optically isolated on each of the 8 outputs, as they should be. But the case is plastic and I doubt this would survive as a road show unit unless embedded inside a sturdy case. Ours are permanently installed so there should be no physical damage. Other than the case, which is of no concern to my installation, I think this is a product of choice as opposed to the $150 units which are built to handle physical abuse. Ours run at the end of 275 feet of cable from the console and there has been no issues with reliability. Man, I love it when I get a great price on something that works!!!

== UPDATE ==After working with the seller, I received a new unit that does work. Overall unit is basically 3 stars, but I gave it an extra star for the excellent support that I received from the seller.Summary: *Very* cheap, but does work as a basic DMX distribution amplifier.I purchased this DMX amplifier because I needed an inexpensive DMX D/A to send along with our bands lighting system. We don't have a lot of money, and our requirements for DMX signaling are very minimal. The issue we were running into at a lot of venues was that we just had too many lights and occasionally the run distance was too long for the USB powered DMX King USB to DMX adapter to drive effectively.I connected the RioRand amplifier directly to the USB to DMX adapter and ran the lights without issue. We typically run 10 no-name LED Par lights that I purchased elsewhere on the internet for next to nothing. The distance from the controller usually ranges from 15 feet to 25 feet depending on the venue. Since most (all) super-cheap LED lights are simply passing the signal along with no isolation and don't re-drive their output, you need to start with a pretty strong signal. This unit allowed all of my lights to work without issue.Build quality:I can't finish this review without discussing the build quality of the unit. The unit itself is made out of a sturdy plastic that should be pretty resistant to most bumps and rough treatment while on the road. HOWEVER: The internals of the unit are a different story. The insides of this unit are not actually attached to anything. When I received this unit, there was some obvious rattling internally when shaking the unit. I took the unit apart to discover that inside is just a single PCB with the wires to the individual jacks. While this isn't a problem in and of itself, the PCB isn't actually attached to anything inside the box. It just kind of "floats" inside held only by the wires that connect it to the external jacks. This probably explains the rattling noise when the unit is shook. I took some peel-and-stick cable-tie anchors and cable ties and attached the PCB to the bottom of the enclosure. It's not perfect, but it should prevent the unit from coming apart internally due to a bumpy ride or a hard jolt.Overall, for the cost the unit performed well in my first few uses, so I can't complain too much. If you need a dirt cheap DMX D/A, this will probably work for you. If you have expensive lighting and require a road-ready DMX distribution amplifier, you might want to look elsewhere.== ORIGINAL REVIEW ==1st one I received didn't work. Waiting on 2nd unit to come in.I'll update my review if the 2nd one works any better.

Bought this to simplify cabling for our band's stage lighting. DMX signal originates from a laptop at the back of the stage, and this allows me to run a cable left, another one right, and a third straight back, instead of having to daisy-chain in a loop around the whole setup (which otherwise necessitates running DMX across the stage). Probably has saved its price in just cable costs alone, but it also brings the advantage of making setup quicker and reducing the total cable footage / number of runs. Great investment, and in 2 shows, not a single issue so far with signaling (we run 14 lights total, almost all of them super cheap generic lights from Amazon).

Very good for the price, we were in a pinch and needed a very cheap DMX 3 pin splitter. It's not he most durable, and the AC adapter can fall out easily sometimes, I'm not super comfortable leaving that connection without taping it. But you get what you pay for and I haven't had any signal issues through this. I wouldn't run a huge rig with these, and at most I've used 3 ports, but it seems to be solid. The case is cheap plastic and the label came off easily but at this price you can't complain.

Tried this splitter several times with different fixtures.Lights would blink and not respond right.This is either a bad splitter or just junkI hooked up a quality splitter (more expensive) and the lights work fine.

I use this to boost the signal to one of my moving head stage lights that wouldn't read DMX signal from my console ( the light worked with another console had ) . I put this DMX amplifier in line at the input and it worked . The light responds to DMX perfectly now . The unit is very useful and economical as hell .Im happy with it