Outdoor Wooden Folding Adirondack Chair Set of 2 with Pre-Assembled BackRest, Wood Patio Chair for Garden Backyard Porch Pool Deck Firepit

I bought 4 of the 2-chair sets and just finished assembling them. They are well engineered to make assembly easy. The real key to assembling them is to not tighten the hinge bolts until the end. The first one took me probably 30 minutes, the 4th one took me about 10 minutes. Come back and read this when you are ready to assemble them. I tried assembling the first one on the floor, but it is much better to clear off the kitchen table (or work bench) and work there. Lay the box on the table, taped seam up. Cut the tape, but not too deep. Open the box and cut the bubble wrap loose. Take out all of the pieces and lay them aside. Dispose of the box and the packing material. Find the two long pieces (back legs) and lay them parallel on the table, with the larger rear cutout notches facing each other. Find the scalloped front piece with the 4 screw holes. Hint: All of the holes are countersunk, so you know which side to screw from. Lay it on the table in front of the the two long read legs, scalloped side down and line up the holes. The scallops actually line up the holes flush. Find the 5 seat slats and lay them out on top of the legs. Unpack all of your screws. Place the screws in the slats (in the countersunk side) and line up the holes. It is easiest to push the screws through the slats slightly to get them to align in the holes underneath. The next piece is the back slat of the seat that is curved and is on the angle edge. Voila, the seat is done. Now. Open the two bags of bolts and split them between either side of the seat. Take the two hinge pieces (8" X1" wood pieces with 2 holes) and connect them to the legs with the nuts and bolts. Big hint: One washer goes on each end of the bolt and one in the middle between the wood pieces. You will screw this up at least once. DO NOT TIGHTEN THE BOLTS! Now turn to the pre-assembled seat back. Find the curved piece that goes on the middle of the back. This is the one step that I still have a little trouble with. You need to line up the 3 holes from the front side, so it is awkward. Tighten the screws. Now lay out the seatback flat at the rear of the seat you just built and line up the open end of the hinge pieces with the bottom rod across the seat back. Again put in your bolt and 3 washers on each side, but do not tighten. Next, find the front legs. The little triangles at the top point outward. Move the seat to the edge of your table and put the bolt through the front leg and back leg, and let it dangle there on each side. You guessed it, do not tighten the bolts. Now take the arms, skinny sides to the back (and middle) and lay them next to the back and seat on the table. Attach them to the middle of the back seat with the bolts. When that is done, pick up the seat back and the arms attach them to the top of the front legs. Remember that these bolts are the only ones that go from the inside out. Now that you have attached all of the bolts, go ahead and tighten them. The last step is then to attach the support across the front with the 4 screws, beveled edge up and countersunk side facing out. It seats real well in the notches provided. Per other's advice, I am going to poly them, and I think I will construct some cup holder to go under the arms as well. I think I will build my own footrests too. They are easy. Hope this helps.

Love these!! They are super comfortable and they were easy to put together with two people! We chose to paint them and we couldn’t be happier!

Not too bad to put together. I thought the chairs look attractive and nice. We have one problem though. One chair was not complete. We’re missing a leg. Will update this. Wrote the seller to try to get a replacement leg without it. the other chair is useless. Outside of that, though we were happy with the chair that is completed.

I thought these would be complicated to put together but they turned out to be pretty simple. The instructions were clear and easy to follow. I used an electric drill which made assembly really quick. The last couple of piece where you have to use their socket-thingy was a little slow going same as using a socket wrench in any tight spot.I have an 8' folding table and bad knees, so I assembled them on the table after Thomas Watersealing them. Recommend sealing. My daughter bought the same set and didn't seal, and her's look pretty weathered. The sealing makes the wood look nice and it will hold up to the harsh Florida sun.

These chairs, while they look cute, are HORRIBLE. Putting each chair together took HOURS and most of the screws still would not go in, not with a drill, not with making the holes bigger, nothing. I have blisters all over my hands and would like to have some words with whoever designed these chairs. I’m not sure if the ones I got were defective or if this is how they all come, but putting these chairs together will take years off your life and they might still fall apart from loose screws that will not go in. DO NOT RECOMMEND.

Hands down the best chair I’ve ever owned. It’s the only chair that doesn’t hurt my back after sitting in for a while.I sat in one of these chairs probably 20+ years ago and never forgot it. Since then I’ve been set on just building one myself. ….. so that never happened even thought I did my research multiple times. 20 years later I see this one on Amazon and it was foldable for ($59 I think) I jumped right on it! It arrived early and I put it together immediately and I’ve been sitting in it ever since. I’m 6’ 235#, this chair fits me perfectly. And it’s feels very sturdy. It did sound stressed when I fell back in it, so I won’t do that anymore. Like anything else, just take care of it.FYI The paint is flat or a primer…. IDK , it works for me. Also, the cheaper price may be from the fact you have to assemble. Not a big deal. After you unpack it will take 30 minutes to an hour for most people. Best to follow instructions. All you need is a drill or Phillips head screw driver the little pocket wrench they supply.I’ll be ordering more soon. The next one I will try an XXL to get more width?

Nice looking. Yes. Affordable. Also yes. A pain in the ass to put together. Absolutely. No parts are labeled and the pilot holes were not drilled well enough to allow screws to go in completely so I've had drill new holes. Probelem is, now I have a drill bit stuck in one of the pilot holes. I guess the wood will be fairly durable once it is assembled but this is ridiculous. Spend a little more somewhere else and save your valuable time.